Mechanical parts

Mechanical parts bruce Thu, 07/26/2018 - 10:32

The Mechanical Part Import Module is used to import a 3D mechanical part from an STL file.

  • Use the New product button to import an STL file. The file is displayed in the 3D viewer.
  • After importing an STL file, you may use the Step button to add a STEP file to the product.
  • After importing an STL file, you may use the Doc button to attach additional files to the product.

The width (X), depth (Y) and height (Z) of the object are displayed. If these dimensions are incorrect, it is because the file units are not millimeters. Click on one of the units buttons to change the object size.

Note: STL files are “unit-less,” which means that they contain only numeric values, without any information about scaling. Macaos Enterprise assumes that the STL file is in millimeters. If the file is in inches, clicking on the in button should display the file with correct dimensions. In the same manner, the other units buttons may be used to select the appropriate scaling.

The volume, weight and total surface area of the object are also displayed.

Material properties

Select the desired material for the mechanical part. A selection of photopolymer or stereolithographic plastics are available for 3D printing. Alternatively, you may select aluminum (with a variety of finishes) for machining. It is also possible to specify a different material.

If a plastic is selected, then you may click on the datasheet link to view the material datasheet.

If a non-transparent plastic material is selected, then you may choose a paint color and finish.

Note: Online prices are not available for machined aluminum parts.

Navigation cube

A navigation cube is shown in the top right corner of the 3D viewer. Click on any face, edge or corner of this cube to rotate the object view so that the selected face/edge/corner is pointed toward the user.

The 3D viewer allows viewing the object from more or less any angle. The available operations are:

Rotate camera viewpoint: Drag with left mouse button. Press Shift to reduce the rotation speed.

Rotate object: Drag with right mouse button. Press Shift to reduce the rotation speed.

Pan along axis: Press X, Y or Z key and drag with right mouse button.

Pan slowly along Y axis: Mouse wheel

Publishing

When publishing the mechanical part product, you will be asked to include a STEP file with the imported product. A STEP file gives more accurate machining information than an STL file, especially if the object contains many detailed curved surfaces. For machined aluminum parts, a STEP file must be included.

Macaos Enterprise needs an STL file to display and calculate the dimensions of a mechanical part. And for simpler parts, the STL file is sufficient for manufacture. However, best results are obtained by importing both files to the product.

Use the Exit button to close the STL import module

Selecting a paint color

Selecting a paint color bruce Wed, 06/17/2020 - 14:28
Select paint color dialog box

A paint color may be specified either as an RAL color, an NCS color, or by specifying HSL or RGB values. It is also possible to select a hue and saturation by clicking the color map and a luminosity by clicking the slider.

All four of these color systems are interrelated, but the transformations between the systems are somewhat imprecise. Therefore, the following precedence applies:

  • RAL color has highest precedence. Selecting a RAL color will display the closest possible transformations to the other color systems. The RAL color will be specified as the paint color.
  • NCS color has second precedence. Specifying a valid NCS color string causes the closest possible transformations to the HSL and RGB color systems to be displayed. If the RGB value is a close match to an RAL color, then the RAL color will be selected and take precedence.
  • If no RAL color is selected and the NCS color string is invalid, then the RGB color is used.

When Find closest matching RAL or NCS color is checked, an NCS color string is automatically calculated whenever one of the other color parameters changes. If there is no matching RAL color then the calculated NCS color string will be selected. If you would prefer that the color be specified as an RGB color, then remove the check mark from Find closest matching RAL or NCS color.